Studentshare
Subjects
Design & Technology
The Fundamental Noise Source in Electronic Circuits

The Fundamental Noise Source in Electronic Circuits - Assignment Example

Summary

Every component in a circuit shows presence of random electrical noise in them which is mostly in terms of current or voltage. This noise may be…

Download full paper File format: .doc, available for editing

GRAB THE BEST PAPER93% of users find it useful

The Fundamental Noise Source in Electronic Circuits

Read Text Preview

Subject: Design & Technology
Type: Assignment
Level: College
Pages: 5 (1250 words)
Downloads: 2
Author: vandervortmicah

Extract of sample "The Fundamental Noise Source in Electronic Circuits"

Download file to see previous pages

A non-inverting amplifier employing an op-amp was intended to amplify the signal V1 from a transducer with source resistance Rs. The amplifier has input noise voltage and input noise current spectral densities of Vniand Ini. The figure below is an inverting amplifier employing an op-amp .The circuit is intended to amplify the signal V1 from a transducer with source resistance Rs. The amplifier has input noise voltage and input noise current spectral densities of Vni and Ini respectively. The figure below shows a differential amplifier employing an op-amp.

The circuit is intended to amplify the signal V1 from a transducer with source resistance Rs. The amplifier has input noise voltage and input noise current spectral densities of V ni and I

...Download file to see next pages Read More

CHECK THESE SAMPLES OF The Fundamental Noise Source in Electronic Circuits

Digital Telecommunications and Networks

Additive noise is the noise produced by electronic circuits.... It is named so because this type of noise accumulates with the addition of electronic components.... Wayne Tomasi, in his book electronic Communications Systems, outlined how a simplex PCM system is integrated in telephony: An analog input signal passes a band pass filter which limits it to the standard voice-band frequency range of 300Hz to 3000Hz.... Digital signals are relatively immune to noise, as opposed to analog signals....

8 Pages (2000 words) Essay

Electrical & electronic principles ( lap report ) AC power

This was followed by connecting the inductance in series with a power resistor, low ohm and an ammeter alongside sketching an impedance triangle for the RL… Part one was completed by carrying out some calculation as displayed in the discussion part. The procedure for this part was a continuation of part one of the Using the oscilloscope, the current and the voltage waveforms supplies were observed and determined alongside determining the lead or lag angle for the circuit....

5 Pages (1250 words) Assignment

Feedback and Oscillators in Electronics

More often than not, feedback is used in electronic circuits for various reasons.... It can also be used in making circuits stable, as well as self-creating and it has an output that can characteristically create equilibrium condition.... Following this, the amplification of signal is then resent to the input where it undergoes amplification once more....

9 Pages (2250 words) Lab Report

Analysis of Electromagnetic Compatibility

the fundamental need was the uninterrupted power supply and safety of data.... Miniature circuits were susceptible to Electrostatic Discharge (ESD) damage.... The first ever EMC issue was from the natural source, namely, lightning.... Switching devices in automobiles, refrigerators, television, radio etc were a source of cause for 'transient interference'....

10 Pages (2500 words) Assignment

Mechanical Design and Optimization of Electronic Systems

"Mechanical Design and Optimization of electronic System" paper states that Most of the fans are powered by bus power, meaning it does not require an external power adapter.... Bond pad refers to the process used to connect the circuit on the die pin on a packaged chip that can result in Electrostatic discharge/ electrical overstress due to the process of the bonding pad creationsThe gate oxide refers to the dielectric layer that separates the gate terminal of a MOSFET from the underlying source and it also drains and which makes it very critical to every transistor – hot carrier injection13....

5 Pages (1250 words) Assignment

RF-Based Wireless Charging and Energy Harvesting

Rectenna is a device that is capable of using capturing microwave by using a power supply that is wireless and then converts the power to DC in order to produce other related devices or circuits that are placed on a chip.... OrCAD capture is a device with schematic solutions that can generate and document electric circuits....

11 Pages (2750 words) Coursework

Design of a Motor Speed Sampling, Amplification, Filtering and Display Circuit

emonstration by calculation gives an error source as the peak-to-peak ripple developed by the unfiltered harmonics.... This removes the noise caused by the DC current (amplifier 1/f noise).... The paper "Design of a Motor Speed Sampling, Amplification, Filtering and Display Circuit" states that using the input signals, the ripple counter was reset to 0 as required....

11 Pages (2750 words) Coursework

Analog to Digital Inverters

"Analog to Digital Inverters" paper contains a summary theory of some electronic devices and systems, including the Analogue to Digital Converter (ADC) and R-2R ladder Digital to Analogue circuit.... nbsp; Analog to Digital converters are used in the entire electronic world.... When a signal is in the digital form, it is less susceptible to the deleterious effects of additive noise....

14 Pages (3500 words) Coursework