Got a tricky question? Receive an answer from students like you! Try us!

Results and Discussion - Essay Example

Only on StudentShare
High school
Author : gust17
Essay
Engineering and Construction
Pages 8 (2008 words)

Summary

Chapter 4- Results of the Experiment The results of the experiment has been given in this chapter in with graphical representation and pictures of the actual experiment that had been conducted for the evaluation of corrosion, tribological and properties of linked wear and tear of the Cr-Co alloy that is used in medical-based implants…

Extract of sample
Results and Discussion

After leaving the substance in the test solution for some time, it is weighted to measure the extent of loss in its weight. It is considered to be the effective method of testing the material’s characteristics. In this chapter, a graphical representation of corrosion testing is given. The corrosion testing was performed with the solution of Nacl with the quantity of 0.9%. Ocp vs time A Pictorial Representation of OCP verses Time with sliding and no-sliding depiction. On x and y-axis, allocation of time and potential mV is given. 4.2 Tribocorrosion The second phase of experiment involves testing the tribocorrosion properties of materials. In the process of potentiostatic measurement, an application of a potential that is constant is applied on the sample with the measurements taken within a period of time. A curve is obtained as a result of this electrochemical process. Here the results of the experiment have been presented in graphical form and in the form of profiles. It has been shown that the effect is of two types in which one consisted of sliding and the other with no sliding. When sliding is done with OCP, it causes damage in the passive film. However, on current, sliding has the effect of increasing it at a significant level. ...
Download paper
Not exactly what you need?

Related Essays

Comparison of Two Sets of Data
The lab report "Comparison of Two Sets of Data" overviews two datasets of gross motor vehicle domestic weights from the year 2002 and from the year 2004. This report applied information from a secondary source for its investigation. The collected data was then subjected to statistical analysis using excel from which cumulative were developed. Further, histograms were developed to facilitate analysis of the two sets of data. …
6 pages (1506 words)
Chemical and Material Engineering
The process of analyzing the mechanical qualities of nc by researchers is gradual since this process is experiencing various obstacles. Manufacture of the nc materials is one of the Chief impediments of the experimental evaluations of its properties. The preparation of nc involves factors, for example, porosity, contamination and residual stress, which significantly influence its mechanical capabilities (Lu, Lu & Sui, 4127). Indeed, a valid evaluation of the mechanical qualities of the nc requires a sample that is deficient of the contamination and residual stress. Such a sample will have to…
4 pages (1004 words)
Introduction Chapter for Swirling Flows
and also in various engineering applications. [1] Aerodynamic drag induced by lift of the wings of an aircraft may also give rise to swirling flows in air. In the engineering applications, particularly where combustion systems are entailed, swirling flows can be defined as continuous jets of fluid in uniform transverse flow that have dynamic and three dimensional (3D) structures. [2] According to a basic definition from Lilley (1977), “Swirling flows result from the application of a spiraling motion, with a swirl velocity component (also known as a tangential or azimuthal velocity component)…
6 pages (1506 words)
report 1
This plot is known as the grain distribution plot and will be used for purposes of this report. More often, a relatively distributed curve shows well graded or a soil which is poorly sorted whilst an extremely steep distribution curve, a curve with steep distribution shows poor grade or sufficiently sorted soil. Objectives of the experiment This lab was developed to determine the distribution of grain size for Concrete & Asphalt materials. This is achieved by determination of the coefficient of uniformity, as well as the coefficient of curvature, . These describe general slope and shape of the…
3 pages (753 words)
Properties of Materials
According to a survey that was carried out by our firm, we realized that many instances windows were severely damaged. Upon keenly studying the damages, it was realized that it was partly due to environmental factors and partly due to poor maintenance. The damages on the widows caused variations in geometric configuration, composition, porosity and adherence of corrosion products. They also cause environmental pollution and humidity and temperature variations. 2.0 BACKGOUND TO THE STUDY Timber has commonly been used in making window frames, because of its accessibility and ease of processing.…
6 pages (1506 words)
Electrical and Electronic Engineering laboratory logbook and report
We also carried out an investigation of the basic bias connections for a transistor. These steps help to familiarize with the basic measurements needed to characterize the properties of transistors. Secondly, we explore the output characteristics of a common-emitter transistor such as load line and operating point and their significance to the operation of a transistor. This laboratory report describes the theory of transistors, methodology used during the experiments, an analysis of the results collected, discussion and conclusion. Background Transistors are three-terminal devices made up of…
6 pages (1506 words)
Introduction to Engineering - Truss Bridge Design
Introduction to Engineering - Truss Bridge Design …
4 pages (1004 words)