Matlab programing Name: Institution: Introduction This task was conducted in a bid to find a solution to the problem of optimizing combination of E12 resistors in series. Resistors are components of electricity which obstruct the flow of electric current and in the process make the current do actual work like lighting, heating, producing sound, magnetism and the like…
It is to see to it that the resistors used are not unnecessarily too many and that the value of resistance that they form in combination are the closest to the desired value of resistance. Problem statement Resistors are measured in SI units known as ohms. In a bid to ease the process of manufacturing in bulk, the manufacturers of resistors usually do it in some standard set measures. These standard resistors are known as E12 resistors. They are the resistors with the values 10 ?; 12 ?; 15 ?; 18 ?; 22 ?; 27 ?; 33 ?; 39 ?; 47 ?; 56 ?; 68 ?; and 82 ? Designers of electrical components who which incorporate the use of resistors usually design for some arbitrary resistance values which shall best suit the requirements of the component under design. Given that resistors are manufactured in the 12 standard values, this implies that the designer shall have make an appropriate combination of a number of the standard resistors to form a value that is as close to the designed value of resistance as is practically possible. The combination should use as few resistors as possible to minimize costs and this calls for proper optimization. In this task, resistors are to be combined in series since resistors combining in series have the total resistance being the sum of the individual resistances of each one of the resistors connected in series. In this problem the designer desires to get optimization modes of combining resistors in series to get the following values of resistances:- 20 ?; 100 ?; 200 ?; 1k ?; 2k ?; 50k ?; 100k ?; 2m ?; 20M ?; 150M ?. Method The method employed in solving this problem takes advantage of the fact that each one of the E12 resistance values form a geometric series, they are all approximately 21% larger than the previous value. The method employed also takes advantage of the fact that for resistors in series, the total resistance is given by summing up the value of each of the individual resistances of the resistors connected in series. i.e, RT = R1 + R2 + R3 The method employed also targeted at making the program user friendly. It was to engage the user in a human like dialogue and hence be usable even by people who have no knowledge of programming. In this regard, the method employed was to write a program code that would ask for some two information from the user of the program. The first information to be inquired from the user is the desired value of resistance (target value). In this case the user would input one of the following as desired; 20 ?; 100 ?; 200 ?; 1k ?; 2k ?; 50k ?; 100k ?; 2m ?; 20M ?; 150M ?. The second information to be inquired from the user is the maximum number of resistors that can be combined. This was introduced in a bid to cut down on the cost of manufacturing. The method employed also involved the use of shorthand in which case, M, K and R were used instead of M ?; K ? and ? respectively. So as to make it possible for the universally accepted and used shorthand used by electrical engineers be input in the program by the users. Results and discussion The program so formed is user friendly and able to ask for the two values from the user, i.e. the value of resistance desired and the maximum number of resistors to be combined. The program is also able to accept values of input written in electrical engineers’ ...
Cite this document
(“Matlab problem Assignment Example | Topics and Well Written Essays - 1250 words”, n.d.)
Retrieved from https://studentshare.net/logic-programming/95692-matlab-problem
(Matlab Problem Assignment Example | Topics and Well Written Essays - 1250 Words)
“Matlab Problem Assignment Example | Topics and Well Written Essays - 1250 Words”, n.d. https://studentshare.net/logic-programming/95692-matlab-problem.
What is the way forward? Since the above issues have been found to be facts, it is necessary to focus on the necessary steps to take in order to stop them from occurring. Some policies need to be formulated in order to offer solutions to the problems. A thorough research needs to be carried out to establish the cause of the problems.
m represents the breakpoints and coefficients of the spline interpolant on successive subintervals, number of polynomial pieces that constitute spline function and the number of coefficients that represent each polynomial pieces, respectively. z1 provided the integral over the
We begin with the Amplitude Modulation and study its types i.e. Double side band with suppressed carrier (DSB-SC) Amplitude Modulation, Quadrature Amplitude Modulation (QAM), Single Side Band (SSB) Amplitude Modulation and
It used data in two “.csv” excel spreadsheet files “daily_output.csv” and “radiation.csv”.
The main objective of the program is to conduct a linear regression exercise using the data in the spreadsheet files and to generate a single output
same point in pregnancy as or earlier than Marcelle, (b) at a later point in pregnancy than Marcelle, and (c) between their due date and the point at which Marcelle gave birth.
Repeat the SPSS Connection from page 105 on your computer. Copy and paste the SPSS output for the
By assuming the longitudinal section is a curve it becomes easier to obtain it because it helps map it into a graph. The following specifies the steps
find(d>0) and find(d<0) were used to obtain the non-zero points and the result was used
The study also observed that a sizeable portion of the heart disease cases is caused by hypertension. It is documented that racial and ethnic disparities exist in the toll of cardiovascular disease that results from hypertension. African Americans are affected more heavily
It is evident from Table 1 that the two systems analyzed in the experiment are under the category of system type 0. This is primarily because, in the step input, they both displayed a real value as an error and in the ramp and parabolic input; they displayed an infinite value error. Figure 1.1.3 illustrated the mode of determination of system types.
9 Pages(2250 words)Assignment
GOT A TRICKY QUESTION? RECEIVE AN ANSWER FROM STUDENTS LIKE YOU!
Let us find you another Assignment on topic Matlab problem for FREE!