INVESTIGATING MATERIALS, THEIR PROPERTIES & MECHANISMS OF MATERIAL FAILURE CONTENTS Number Topic Pages 1 Materials and Range of Properties 1-2 2 Test Procedures For Material Properties 3 3 Manipulative Process Impact on Material Properties and Limitations 4 Bibliography 5 Materials and Range of Properties Materials can be majorly classified in three considerable categories i.e…
Ferrous metals are those metals that contain iron as a considerable constituent in it whilst non ferrous metals are free from iron metal. Ferrous metals are magnetic in nature therefore these are used in different applications that involved the usage of electro magnets. Iron is usually present in diverse ores structure. Therefore the ore is treated to yield iron metal and normally it is done by melting the ore in a blast furnace. Non Ferrous metals include a long list of metals some of these metals are copper, aluminum and lead etc. Copper metal is widely used in electrical wires due to its high conductivity for electric current. Copper is generally really very soft and can be drawn into wire easily. Aluminum is also a metal which is relatively similar to copper in its properties because it is also very soft and malleable just like copper, mainly aluminum is utilized in aluminum sheets and foils. Unlike iron aluminum has a lower melting point of 659 degree centigrade while that of iron is about 1530 degree centigrade. Aluminum can be easily manipulated through machining, casting, drawing and extrusion. Lead is a special type of heavy metal; it is a bluish-white metal that has insufficient conductivity of electrical charges when evaluated against the majority of other metals. But due to lead’s ductility, malleability and softness it is mixed with other metals to make them ready for machining operations. Polymers are also recognized as macro molecules which are composed of recurring molecular structures. Polymers are based on very long plastic ranges. Polymers cover different mechanical properties that include extensive levels of strength, toughness and hardness. There are mainly three types of polymers, these are thermoplastics, thermosetting and fiber reinforced plastics (FRPs). FRPs are also replacing some metals in various applications for better. Since FRPs are of high strength, durability and furthermore these are flexible and light weighted therefore the rear and front body of heavy automobiles like buses are contemporarily replaced by these FRPs in place of a metallic sheet. Ceramic is a substance which is manufactured from inorganic and nonmetallic constituents. The constituents are subjected by the application of heat and consequent cooling. Ceramics are extraordinarily hardened, thus types of ceramics are used as manipulative tools for example as in the case of grinding wheels. Ceramics have high melting point therefore ceramics are used in furnace linings and other high temperature applications. Ceramics are high heat absorbers therefore these are also used in storage heaters. Ceramic balls are also manufactured to substitute steel in ball bearings. The higher hardness of ceramics explicates that these are slighter disposed to wear out and can be more durable that steel ball bearings. The distortion phenomenon under load in ceramics is also reasonably small as compare to metals. In greater speed, heat from abrasion during rolling can originate troubles for metal bearings, which can be minimized by ceramics. Ceramics are additionally chemically insolent and can be utilized in wet condition where steel bearings could oxidize. The main shortcomings in ceramics are considerably sophisticated cost and vulnerability to break under shock loads. 1. Test Procedures for Material Properties Material testing procedures are actually governed by American Society for ...
Cite this document
(“Materials Engineering Essay Example | Topics and Well Written Essays - 1000 words”, n.d.)
Retrieved from https://studentshare.net/environmental-studies/36677-materials-engineering
(Materials Engineering Essay Example | Topics and Well Written Essays - 1000 Words)
“Materials Engineering Essay Example | Topics and Well Written Essays - 1000 Words”, n.d. https://studentshare.net/environmental-studies/36677-materials-engineering.
In the experiment conducted two mixture were used to produce stainless steel. The one this report has special emphasis in the one with boron added to the powder mixture. Over the course of the report, certain aspects of boron and its effectiveness as a alloy element in ferrous mixtures will be discussed.
They were required to determine whether the bridge was in a position to withstand the rapid transit scheme proposal as well as to accommodate a 4 m wide footway. The scope of the project was the proposed bus way scheme. After an extensive research, the group was able to conclude that Ashton Swing Bridge was in a suitable position to accommodate two lanes of traffic.
This is classified into three groups. These are, simple diffusion transformation which has no change in the number of composition. Examples of which are the solidification of pure metal. More complex diffusion dependent transformation consist of some alteration in phase composition and the number of phase present with an example of eutectic reactions.
So that McKinley Construction can submit It's bid on the new bid form.
The agency hearing the case, not clear if McKinley had indeed committed to the exact terms of the addendum properly rejected the bid due to irregularity. Despite submitting what may be the best bid, irregularity in the- documents required and that which McKinley submitted made it difficult to determine whether McKinley had indeed committed to the exact terms of the addendum sent to it by the department of agriculture.
Materials once selected can be further processed through heat treatment etc. in order to impart additional specific properties. Databases of various materials are available, codified as national standards and unified at international level for comparison and use.
million cycles at 2 N load will last for only about 1.56 million cycles if the service load increases to 8 N or a four fold increase in the applied load reduces life of a bearing by a factor of 64.
Liquid lubricants need to be applied at regular intervals due to various reasons
Plastic deformation is one of the most important techniques of manufacturing in case of metals (Boljanovic, 2004: 13). Metal is usually available in the forms ingots from the furnaces and it has to be converted into desired form or shape in a manufacturing