Terminating Fiber Optic Cable Using a Polish Method ,Testing Wired Media Both Copper and Fiber - Essay Example

Terminating Fiber Optic Cable Using a Polish Method, Testing Wired Media Both Copper and Fiber Terminating Fiber Optic Cable Using a Polish Method For termination of fiber optic a connection must be provided to a device, for instance to a wall outlet or other equipment that will allow for connecting the cable to other additional cables or systems/devices. Additionally, the basis of fiber optic termination is to generally assist fiber cross-connection and light wave signal’s supply. In addition, suitable fiber optic termination will protect the fibers from dirt or damage as it is used to avoid extreme loss of light, thus, it makes a network more reliable to implement more smoothly as well as efficiently (CableOrganizer.com, Inc. Company).

For the termination of fiber optic, we first start the preparation for fiber termination that generally contains the procedure for gathering the supplies that we will furthermore require, cutting the Kevlar, stripping the outer jacket and buffer or coating. For supplies, we will definitely require safety glasses, connectors, a fiber disposal bin, epoxy and syringes, fiber optic cable and a polishing film.In addition, tools that are used in fiber optic termination consist of fiber notch, stripper, adjustable cable jacket stripper, Aramid fiber scissors, polishing glass plate, polishing puck plus a rubber pad to polish the PC connectors whose sole purpose is the single mode termination (CableOrganizer.com, Inc. Company).

During this process we will prepare the fiber optics for termination. First we remove the cladding and the cover and then pursue the following steps: Fill the syringe by ready to use paste. Strip back the outer shield of the cable by using a rotary stripping tool. Restrain the Aramid safety component with ceramic or Kevlar scissors. Slide the twist relief boot onto the fiber to be terminated. Afterward Strip the main buffer of the fiber by using fiber strippers and be careful not to use ordinary wire strippers.

Here we need to apply this on a small section at a time to avoid the fiber optic fracture, approximately 10mm (3/8 inches) on each cut will be fine until or unless we get used to it. Strip back about 30mm (1.25 inches). Then we will fix the connector. Then we need to inject the paste into the connector’s body for an expectation of a small drop that might comes out at the end of the ferrule. Clean the uncovered fiber by using fuzz free wipe as well as isopropyl alcohol, you would see that it will "squeak" when it is clean.

Afterward we will apply the primer to the bare fiber either by using the brush supplied or by dropping it into the bottle. After that we will push the fiber into the connector’s body in a smooth action until the buffer reaches the back of the ferrule. Then during the process of cutting, we need to make sure that it breaks cleanly at an angle of 90 degrees, while we can consider that as it is ground down to the ferrule and then polishing it wouldnt make any difference if it were just broken.

In the next step we will gradually cut the fiber as close to the ferrule as possible and then use a small tug to break the fiber’s end away. However, during the polishing step we put the fiber down to the ferrule, for this purpose we use about a 9 micron lapping film. Now we will grip the connector in one hand and rub the nub of fiber downward to the ferrule by means of lapping film. Until it is close enough to feel that it is getting smoother. Then we pop in the connector into the polishing puck, so that it keeps it vertical to the polishing surface.

Now at this time we will place a sheet of 2 micron lapping film on an appropriate smooth surface. Then we will grasp the connector as well as puck, and then leave it on the polishing surface. Consequently we can have a visual check and also testing of the overall termination of fiber optic (CableOrganizer.com, Inc. Company) & (Fiber Optics For Sale Co.). Testing Wired Media Both Copper and Fiber For testing of cable medium we have to test the cable from the both ends. This test can only be efficiently done when both ends are finished then fiber can be tested.

Additionally, the Fiber testing is used to employ a bulky OTDR (Optical Time Domain Reflectometer) driven through a geek by way of a degree concept in optical physics. However, recently a very simple hand-held light source and power meter can be employed for this purpose. To offer a full test we are capable to use a fiber certification tools that simply tells us for what system the fiber is good for. These fairly simple to use (but quite expensive) tools will provide a print out of the whole testing parameters along with losses and the communications media it will work on during testing (CableOrganizer.com, Inc. Company) & (Fiber Optics For Sale Co.). Work CitedCableOrganizer.com, Inc. Company.

"FIBER OPTIC INSTALLATION AND TERMINATION." 2010. 29 July 2010 .Fiber Optics For Sale Co. "What is fiber optic cable termination?" 2010. 28 July 2010 .