StudentShare solutions

# The earthquake resistant concrete frame building with special focus on beams and columns - Dissertation Example

Only on StudentShare

## Extract of sampleThe earthquake resistant concrete frame building with special focus on beams and columns

According to the research findings it can therefore be said that special condition should be followed when the beam elements are being designed such as the difference between rectangular beam and flanged beam should be known. Flanged beams are generally the rectangular beams which work with slabs and the part of slab element acts with the top part of the beam. If it is below the flange, then the section needs to be designed by taking into consideration the specific area of concrete section for compression part. The most crucial part in design is the design for flexure and shear. The flexure design has to be repeated twice, one for support condition and another for span condition. Shear force which acts to the beam can have a substantial deformation. This deformation occurs particularly to the both ends of the beam. The ultimate shear capacity Vn of a section of a beam equals the sum of the nominal shear strength of the concrete Vc and the nominal shear strength provided by the reinforcement Vs; that is, ΦVn = Vc = Vs. The factored shear force Vu on a section should not exceed where Φ = capacity reduction factor (0.85 for shear and torsion). Except for brackets and other short cantilevers, the section for maximum shear may be taken at a distance equal to d from the face of the support. The shear Vc carried by the concrete alone should not exceed 2√fc_ bwd is the width of the beam web and d, the depth of the centroid of reinforcement. ...

## Summary

In this paper we are going to compare two codes on the basis designing the earthquake resistance concrete frame building. The comparison focuses around beam and columns of the building. Two codes are compared here. First is Iranian concrete code and the second one is Eurocode…
Author : tpollich

### Related Essays

Design of Concrete Frame based on Iranian Code (2800) and Eurocode (EC 8) for Resistance to Earthquake.
Another incident claimed 1000 people in 1981 in Kerman while 40,000 faced the same in Gilan, a province in Northern Iran. The Ritcher scale reading struck 7.2. An earthquake that occurred in Bam in December 2003 is numbered among the 130 major earthquakes in Iranian history with estimated casualty cases of 30-50 thousand (Iranian Studies Group, 2004, p.2). The foundation of assessment of seismic hazard in Iran is on the frequency of seismicity in relation to time and space. In the assessment of seismic hazards, seismotectonic sources are considered. The success of this study relies on regional...
15 pages (3765 words) Literature review
Steel building design
At the same time, the design should also ensure and provide the necessary comfort, energy-efficiency and safety to the inhabitants. To attain the fundamental building requirements, it is then necessary to integrate adequate structural resistance to building designs. The primary purpose of this is to sustain the actions (i.e. loads, imposed displacements, thermal strains) and influences resistance so that the building will remain serviceable and durable (Brettle, 2009). Meanwhile, in order to secure the structural safety of the building during its intended life, it should be designed and...
20 pages (5020 words) Coursework
Seismic Response of Reinforced Concrete Frame Buildings with Different Ductility Classes Using EC8 and EC2
The paper tells that over the years gradually there have been greater advancements in the various concrete structures and measures that can be applied for the construction of buildings. In the present times, thus, the strength theory is significantly considered in building constructions. Load factors have been found to be necessary for the determination of the concrete structures used for the construction purposes. The strength theory focuses on the ultimate strength design that makes use of inelastic strains thus distributing the stress of loads uniformly. The concept of reinforced concrete...
49 pages (12299 words) Dissertation
Seismic action and methods od analysis
Earthquakes trigger one mode of vibration which is the lowest fundamental mode besides higher modes which take place as a result of tremors. 2.1 Development of Seismic Regulations The Building Seismic Safety Council was put up in 1997 as an affiliate of National Institute of Building Sciences. Its main purpose is to promote safety of the public by providing guidelines to construction, designing, planning, utilization and regulation of buildings. It deals with reduction of risks posed on buildings by earthquakes. The main areas which the Building Seismic Safety Council focuses on are...
10 pages (2510 words) Dissertation
Concrete Constituent and Mix Design
Natural heavyweight aggregates include materials such as goethite, limonite, barite, illmenite, magnetite, and hematite, with specific gravities (SGs) ranging from about 3.5 up to about 5.3, leading to concretes with unit weights up to about 4100 kg/m3 . For higher unit weight concretes, synthetic materials such as Ferro phosphorous (SG 5.8 to 6.8) or scrap iron and steel punching (SG 7.8) can be used, with resulting concrete unit weights of up to 6100 kg/m3. High-density aggregates are good attenuators of gamma rays and of fast neutrons, hence their use in radiation shielding. Although...
6 pages (1506 words) Essay
Seismic Analysis and Response of Bare and Masonry-Infilled Reinforced Concrete Frame Structures
Since the infill walls play some roles during earthquakes, their design need consideration to withhold lateral forces. From a research conducted out, most concrete structures succumb to seismic loads due to: Failures of beam-column joints as a result of poor reinforcement at the joints and/or poor workmanship in installation of reinforcement beams; Basic failure that results from flexural weakness and or low shear strength; Failure of the infill wall that results from enough shear strength or a flexural strength that is out-of-plane (Griffith, Mike 2008, p.2). The relationship between...
6 pages (1506 words) Coursework
design and construction of a prestressed concrete tank
The principle behind the prestressed concrete tank is that the compressive stresses induced by the high-strength steel tendons inside a concrete member prior to the loads being applied will balance tensile stresses inflicted in the member during the service. It`s recognized that prestressing eliminates several design limitations and conventional concrete places on load and span and allows the building of roofs, bridges floors, and walls with elongated unsupported spans. With this in mind, architects and engineers design as well as build lighter concrete tanks without sacrificing strength. This...
8 pages (2008 words) Literature review
Got a tricky question? Receive an answer from students like you! Try us!